<sigh...>

I made the mistake of disassembling the caps lock key on my Corvus Concept keyboard (Keytronics of same vintage as Lisa). I had the little pin, but could not get it together again and eventually lost it in my fumbling.  A pox on Keytronics for not spending the extra $0.02 it would have taken to make caps-lock toggle in software.  If anyone comes up with a mod to add this after the fact, I would love to know about it.

On Monday, September 10, 2018 at 8:47:34 PM UTC-4, Ray Arachelian wrote:
A couple of months ago, George Foumakis contacted me about fixing a Lisa
capslock key.

He posted the photo here: https://postimg.cc/image/lwpyl31uj/


In the photo at the url above, from left to right in the image in the url:

0.a very tiny, easy to lose gold pin, one side thicker, one side
thinner. The thick side goes inside a small hole in the white plastic
plunger, the thinner side sticks out and fits into 1:

1. a small white grooved plastic - one side (shown above) shows a
grooved line in the center, the back side shows a groove that looks like
an OR gate. The "output" pin of the OR-gate goes to the bottom where the
gold pin is.

2. a small black bracket - the vertical slot fits the grooved line of 1,
and this fits into against the bottom side of the keycaps (towards the
space bar)

3. A closing cap that fits over the capslock key - if your capslock key
is functioning DO NOT OPEN this. It's very difficult to put it back
together again, and the pin (0) is very very very tiny, much smaller
than it looks in the photo and very easy to lose.
If you must open your capslock key do so carefully in a well lit,
contained environment, and it's very easy for the parts to go flying off
under the table.

It seems that I lost the pin (0) from one of my keyboards by being too
hasty in opening 3 - you've been warned.


I've also attached 3 photos to this message showing how this all fits
together.

The photo named 20180910_172818_resized in the attachments to this email
show the gold pin, and how 1 and 2 fit together.  However the white
grooved plastic bit (1) should be pushed towards the right when putting
the capslock key back together.
The tip of 1 that points towards the gold pin goes to the bottom of the
outside of the capslock square. The gold pin 0 fits into this groove and
the groove implements the locking mechanism.

The 20180910_174807_resized photo shows the capslock key - this is the
one that's in the middle on the rightmost row - the space bar would be
to the bottom of this - you can identify the capslock key in this
picture because it has a vertical opening to the right.
If you look very closely at the bottom of this opening you can see the
gold pin stick out thin end to the outside.

The opening inside the capslock plunger may have a hidden tiny spring
there, as pushing the pin in causes it to jump out - yet another thing
that makes it very difficult to put back in, and easily lose the pin as
it will go flying.  I've not taken the plunger apart so I don't know if
that's the case or not.


20180910_172604_resized shows the  assembled caps lock key with the
closing cap (3) in place.

Hope this is useful to someone, however, again, heed the warning, should
you open the closing cap (3), you can expect that the parts 0-2 will go
flying and you may lose the tiny pin and break your capslock, so unless
you have a very good reason, don't open it.


I'll add this to LisaFAQ eventually.

--
--
-----
You received this message because you are a member of the LisaList group.
The group FAQ is at http://lowendmac.com/lists/lisa.html
To post to this group, send email to lisalist@googlegroups.com
To leave this group, send email to lisalist+unsubscribe@googlegroups.com
For more options, visit this group at http://groups.google.com/group/lisalist
---
You received this message because you are subscribed to the Google Groups "LisaList" group.
To unsubscribe from this group and stop receiving emails from it, send an email to lisalist+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.